MS1471

The MS1471 is a piezoresistive silicon pressure sensor packaged in a surface mount configuration. It is intended for high volume applications where small size, light weight, low cost, and compatibility with automated assembly equipment are required. Offset and span are calibrated at room temperature for OEMs requiring higher accuracies.

FP1124

The FP1124-3 HT Series of pressure transducers is designed specifically to measure pressure on the brake circuit, including ABS brake systems. With its rugged design and excellent thermal characteristics, the FP1124-3 is built to withstand high temperatures to fit most braketest applications. Additional IP67 protection and a bleeder screw ensure ease of use and long life even under severe environmental conditions. The sensor can be powered by a car battery and delivers direct high-level 0.5 to 5.5 Vdc output signal.

MS5701

The MS5701 is a new generation of high resolution differential pressure sensors with SPI and I2C bus interface. It is optimized for water level measurement until ~50 cm. The sensor module includes a high linear pressure sensor and a ultra low power 24 bit ΔΣ ADC with internal factory calibrated coefficients.

MS5561C

The MS5561C is a SMD-hybrid device including a precision piezo-resistive pressure sensor and an ADC-Interface IC. It uses a three-wire serial interface for communication. The module dimensions of 4.75 mm x 4.25 mm and a height of only 1.6 mm allows for up-to-date SMD design. It provides a 16 bit data word from a pressure and temperature dependent voltage. The MS5561 is a low power, low voltage device with automatic power down (ON/OFF) switching. A 3-wire interface is used for all communications with a micro-controller.

DP86 Series

The DP86 Series differential pressure sensor is a double-sided, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. The series can be configured for o-ring mounting or threaded process fittings.

85 Flush Mount

The 85 Flush Mount is a small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. The 85 Flush Mount is designed for o-ring mounting where the diaphragm must not be shrouded by weld ring or fitting.  The sensing package utilizes silicon oil to transfer pressure from the 316L stainless steel diaphragm to the sensing element. A ceramic substrate is attached to the package that contains laser-trimmed resistors for temperature compensation and offset correction. An additional laser trimmed resistor is included which can be used to adjust an external differential amplifier and provide span interchangeability to within ±1%.

MSP100

The MSP100 series pressure transducers provide stainless steel media compatibility for the price of competing plastic sensors. This sensor has no silicone gel or polymeric media isolation methods to fail in contact with water or other harsh chemicals. The all metal diaphragm design is immune to pressure fluctuations and subsequent damage. The all-metal pressure enclosure has a small round plastic housing and is available with a cable and connector. Pressure connections are provided via an O-ring seal. Both compensated/calibrated and uncompensated versions are available. High volume port options are customer specific. The small size vs. performance  and media compatibility are provided through solid-state Microfused™ technology

MSP300

The MSP300 pressure transducer sets a new price performance standard for low cost, high volume, commercial and industrial applications. This series is suitable for measurement of liquid or gas pressure, even for difficult media such as contaminated water, steam, and mildly corrosive fluids.

MSP340

The MSP 340 series of pressure transducers is suitable for measurement of liquid or gas pressure, even for difficult media such as contaminated water, steam, and mildly corrosive fluids. The transducer pressure cavity is machined from a solid piece of 174 PH stainless steel. The standard version includes a 1/4 NPT pipe thread allowing a leakproof, all metal sealed system. There are no Orings, welds or organics exposed to the pressure media. The durability is excellent.

M5100

The M5100  series pressure transducers set a new price performance standard for demanding commercial and heavy industrial applications. This series is suitable for measurement of liquid or gas pressure, even for difficult media such as contaminated water, steam, and mildly corrosive fluids.

U5100

The U5100 series pressure transducers set a new price performance standard for demanding commercial and heavy industrial applications where high accuracy is required. This series is suitable for measurement of liquid or gas pressure, even for difficult media such as contaminated water, steam, and mildly corrosive fluids.

D5100

The D5100 series sets the price and performance standard for differential pressure transducers used in demanding environments. The amplified model of the D5100 series exceeds the latest heavy industrial CE requirements including surge protection and reverse polarity protection.

US300

US10000

The US10000 series is the first choice for applications requiring high accuracy in a rugged environment. The 0.05% accuracy and typical total error band of 0.25% provides a stable platform for test stands and high accuracy industrial pressure applications.

XPM4

The XPM4 is a miniature transducer designed to measure static and dynamic pressure under a wide variety of conditions, including hostile environments. The all-titanium construction and flush diaphragm protect the sensor against most corrosive environments.

XPM5

The XPM5 is a miniature transducer designed to measure static and dynamic pressure under a wide variety of conditions, including hostile environments. The all-titanium construction and flush diaphragm allow the sensor to withstand most corrosive liquids. 

XPM6

The XPM6 is a miniature transducer designed to measure static and dynamic pressure under a wide variety of conditions, including hostile environments. It is made of stainless steel and is available in ranges from 0-100 to 0-1000 bar [1500 to 15 000 psi]. 

XPM10

The XPM10 is a miniature transducer designed to measure static and dynamic pressure under a wide variety of conditions, including hostile environments. It is made of stainless steel or titanium and is available in standard ranges from 0-1 to 350 bars [15 up to 5000 psi].

P900

Standard versions of this transducer use a 17-4 PH stainless steel diaphragm to sense pressure (Inconel versions are available for operation in highly corrosive environments). The deflection of the diaphragm is transferred to a double cantilever beam by a force transfer rod. Strain in the beam, and therefore input pressure, is measured by four foil strain gauges. An all-welded construction provides high reliability and stability.

P1200

The P1200 Series pressure transducers and transmitters provide high accuracy pressure measurement of liquids and gases.  These robust transducers combine hybrid electronics with highly reliable strain gauge sensing technology to offer superior performance in rugged applications. Constructed from media compatible 17-4 PH stainless steel, the P1200 provides exceptional performance in extreme environments.

P700

P700 series pressure transducers are designed for high reliability and stability. The all welded construction incorporates a double cantilever beam with bonded foil strain gauges. Coupling to the pressure diaphragm via a force rod, gives excellent thermal isolation from the fluid or gas being measured. High overload protection is an integral part of the design. These units are capable of sensing extremely small changes of applied pressure and are relatively insensitive to vibration, altitude and shock.

P105

The P105 is a high pressure transducer designed to measure static and dynamic pressure under a wide variety of conditions, including hostile environments. The mechanical design and a stainless steel diaphragm allow the sensor to withstand most aggressive liquids.

50

The 50 is a piezoresistive silicon pressure sensor packaged in a TO-5 configuration. Absolute pressure ranges from 0-15 to 0-500 psi are available. It is intended for high volume applications where small size, light weight and low cost are required. This design is intended for non-corrosive gases and is not recommended for liquids. A gel filling can be applied to provide mild protection against humidity and dust.

9000

The 9000 Series CANbus pressure transducer meets the demands of the test and measurement industry, including automotive and marine applications, with high levels of accuracy over a wide temperature range. The digital output in engineering units eliminates the need for user system calibration.

MS1451

Piezoresistive silicon die technology, temperature compensated, and they are suitable for use with non-corrosive gases. 

13 43

The 13 and 43 are temperature compensated, piezoresistive silicon pressure sensors packaged in a TO-8 configuration. It provides excellent performance and long-term stability. Integral temperature compensation is provided over a range of 0-50°C using laser-trimmed resistors. 

13 43 Std

The 13 and 43 are temperature compensated, piezoresistive silicon pressure sensors packaged in a TO-8 configuration. It provides excellent performance and long-term stability. Gauge and absolute pressure ranges from 0-2 to 0-250 psi are available. Integral temperature compensation is provided over a range of 0-50°C using laser-trimmed resistors. An additional laser-trimmed resistor is included to normalize pressure sensitivity variations by programming the gain of an external differential amplifier. This provides sensitivity interchangeability of ±1%.

27-37

The 27 and 37 UltraStable™ are high performance, temperature compensated, piezoresistive silicon pressure sensors packaged in a TO-8 configurations. It uses Measurement Specialties’ proprietary UltraStable™ die to provide excellent performance and long-term stability over wide temperatures. Gage and differential pressure ranges from 0-15 to  0-250 psi are available. Integral temperature compensation is provided over a range of -20ºC to  +85ºC using laser-trimmed resistors. 

23-33 Psi

The 23 and 33 are temperature compensated, piezoresistive silicon pressure sensors packaged in a TO-8 configuration. It provides excellent performance and long-term stability.
Integral temperature compensation is provided over a range of 0-50°C using laser-trimmed resistors. 

23-33 Std

The 13 and 43 are temperature compensated, piezoresistive silicon pressure sensors packaged in a TO-8 configuration. It provides excellent performance and long-term stability. Gage and absolute pressure ranges from 0-2 to 0-250 psi are available. Integral temperature compensation is provided over a range of 0-50°C using laser-trimmed resistors. 

89 Series

The 89 series is a small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing featuring 5/16-32 UNEF threads and can be welded in place. The 89 is designed for high pressure OEM applications where compatibility with corrosive media is required. The sensing package utilizes silicone oil to transfer pressure from the 316L stainless steel diaphragm to the sensing element.

87N Series

The 87N series is a small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. The 87N is designed for high pressure OEM applications where compatibility with corrosive media is required

85 Series

The 85 series is a small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. The Model 85 is offered in a weldable package or with a variety of threaded fittings such as 1/4 and 1/8NPT, 1/4BSP as well as custom process fittings. The sensing package utilizes silicone oil to transfer pressure from the 316L stainless steel diaphragm to the sensing element.

86 Series

The 86 series is a small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. The 86 is designed for o-ring mounting and OEM applications where compatibility with corrosive media is required. The sensing package utilizes silicone oil to transfer pressure from the 316L stainless steel diaphragm to the sensing element.

86A Amplified

The 86A is a small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. The 86A is designed for o-ring mounting. The sensing package utilizes silicone oil to transfer pressure from the 316L stainless steel diaphragm to the sensing element.  The 86A is designed for high performance, low pressure applications. A custom ASIC is used for temperature compensation, offset correction and provides an amplified output of 0.5 to 4.5V.

154N Series

The 154N series is a small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing.  The 154N is designed for o-ring mounting and OEM applications where compatibility with corrosive media is required.  The sensing package utilizes silicone oil to transfer pressure from the 316L stainless
steel diaphragm to the sensing element.

82C

The 82 series is a 19mm small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. They are designed for o-ring mounting and OEM applications where compatibility with corrosive media is required

82U

The 82 uncompensated is a 19 mm small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. The 82 uncompensated is designed for o-ring mounting and OEM applications where compatibility with corrosive media is required. The sensing package utilizes silicone oil to transfer pressure from the 316L stainless steel diaphragm to the sensing element.

82 Series

The 82 series is a 19mm small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. They are designed for o-ring mounting and OEM applications where compatibility with corrosive media is required. The sensing package utilizes silicone oil to transfer pressure from the 316L stainless steel diaphragm to the sensing element.

LT10

Electronic transmitter with submersible measuring probe in stainless steel for level measurement in vessels where pressure connection in the bottom is not possible or desirable. For example pump pits, reservoirs or plastic tanks.

LT100

Level transmitter with submersible probe in stainless steel for level measurement  in vessels where pressure connection in the bottom of the vessel is not possible or desirable. For example pump pits, reservoirs or plastic tanks.

PT60

A series of pressure transmitters with great flexibility. Modulary built. A wide range of process connections and electronics can be choosen.

82CV

The 82 constant voltage is a 19 mm small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. The 82 constant voltage is designed for o-ring mounting and OEM applications where compatibility with corrosive media is required. The sensing package utilizes silicone oil to transfer pressure from the 316L stainless steel diaphragm to the sensing element. A ceramic substrate is attached to the package that contains laser-trimmed resistors for temperature compensation and offset correction.

1200/1600

The 1200 series pressure transducer features stability and toughness via its CVD and ASIC design coupled with a thicker diaphragm. The thicker diaphragm enables these pressure transducer sensors to survive most pressure spikes caused by pump ripple, solenoid valves, etc. The 1600 series extends the packaging options by providing an all welded stainless steel back end for demanding industrial applications. A modular design allows special ordering of fittings, electrical cables, etc. for OEM applications. The ASIC and CVD technology enables Gems™ to offer almost any output over any pressure range.
 

2200/2600

The 2200 series pressure transducer features stability and accuracy in a variety of enclosure options. The 2600 extends the packaging options via an all welded stainless steel back end for demanding submersible and industrial applications. The 2200 and the 2600 pressure transducers feature proven CVD sensing technology, an ASIC (amplified units), and modular packaging to provide a sensor line that can easily accommodate specials while not sacrificing high performance.

4700

The 4700 series provides precise laboratory type measurements in a rugged industrial package complete with turndown capabilities. Exceptional levels of stability and other performance specifications are achieved by using a sputtered sensing element, which achieves a molecular fusion of a strain gauge material, an insulating material, and the 17-4 PH ss sensing element. Sputtered or thin film technology provides years of worry free.

5000

The 5000 series pressure transducer features a sturdy ceramic diaphragm that detects minute pressure variations, while withstanding large pressure spikes. The tough ceramic sensor is housed in a stainless steel case to ensure performance in the most demanding applications. Both voltage and 4-20 mA outputs are available at time of order. A switch and potentiometer can be accessed for field adjustment of range with 3:1 ranging capability.

MS5401 / MS5407 / MS5412

The MS54XX SMD pressure sensor series is designed for pressure sensor systems with highest demands on resolution and accuracy. The device consists of a silicon micromachined pressure sensor die mounted on a 6.2 x 6.4 mm ceramic carrier or a 6.1 x 6.3 mm PCB protected by a metal or plastic cap. The MS54XX can be delivered in a high sensitivity version giving a maximal output voltage or in a high linearity version. 

MS4525

This series contains both analog output (MS4515/MS4525) and digital output (MS4515DO/MS4525DO) where the digital output versions feature either I²C or SPI interface and provide 14-bit pressure as well as 11-bit temperature sensing. 

MS4525DO

The transducer is built using Measurement Specialties’ proprietary UltraStable™ process and the latest CMOS sensor conditioning circuitry to create a low cost, high performance Digital Output Pressure (14bit) and Temperature (11bit) transducer designed to meet the strictest requirements from OEM customers.

MS5607

The MS5607-02BA is a new generation of high resolution altimeter sensors from MEAS Switzerland with SPI and I2C bus interface. It is optimized for altimeters and variometers with an altitude resolution of 20 cm.

P9000

The P9000 Series is a range of advanced, digitally compensated pressure transducers. The unique design of the P9000 pressure transducer utilizes the proven reliability of strain gauge technology and innovative digital compensation electronics.

P101

ATM/K

Compact and robust stainless steel assembly 1.4435 (316L). Capacitive ceramic sensor without oil filling.
High resistance and overpressure. Gauge or absolute. Complies with the EMC directive 89/336/EEC.
High reliability. Short delivery time. Customized versions. Reverse polarity and short circuit protected.

ATM/F

The ATM/F series 25 is part of a comprehensive range of transmitters specifically designed for the process industry where the fluids are of a clogging nature requiring a flush mount type of installation. Exceptional reliability is achieved with the high overpressure rating, and the combination of high accuracy and good long term stability offer the user reduced recalibration requirements resulting in a low cost of ownership.

ATM/F/Ex

The ATM/F series 25 is part of a comprehensive range of transmitters specifically designed for the process industry where the fluids are of a clogging nature requiring a flush mount type of installation. Exceptional reliability is achieved with the high overpressure rating, and the combination of high accuracy and good long term stability offer the user reduced recalibration requirements resulting in a low cost of ownership. Modular design provides manufacturing flexibility and fast delivery.

ATM.1ST

The ATM 1ST is an electronically compensated pressure transmitter providing a voltage or 2-wire, 4-20 mA analog output. The transmitter offers accuracies of ≤ 0.05% FS or ≤ 0.1% FS including linearity, hysteresis, repeatability, zero and span setting errors. Modular construction and the 20 year proven history of STS piezoresistive sensor technology provide manufacturing flexibility and offers fast delivery for all pressure ranges.

ATM.1ST/Ex

With compact housings in stainless steel or titanium, measuring ranges of up to 1000 bar and reverse polarity/ short circuit protection included, the ATM.1ST/Ex pressure sensor provides the ideal solution for industries where reliable and accurate pressure sensing is required within hazardous areas. The ATM.1ST/Ex has industry leading specifications that include:    

Up to three times full scale overpressure. Accuracy of 0.10% FS on the ATM.ECO/Ex and 0.05% FS on the ATM.1ST/EX. IECEx SEV 10.0003 certification for mining Gas Group 1. Temperature ranges of up to 150 deg C.

ATM.ECO

Compact and robust stainless steel assembly 1.4435 or titanium.  Piezoresistive measuring element.
Measuring ranges from 0…100mbar to 0…1000bar.  Calibration available for all common pressure units.
Reverse polarity and short circuit protected.  High EMV stability.  Customized versions due to modular assembly.

ATM.ECO/Ex

With compact housings in stainless steel or titanium, measuring ranges of up to 1000 bar and reverse polarity/ short circuit protection included, the ATM.ECO/Ex  pressure sensor provides the ideal solution for industries where reliable and accurate pressure sensing is required within hazardous areas. The ATM.ECO/Ex  has industry leading specifications that include:

Up to three times full scale overpressure,  accuracy of 0.10% FS on the ATM.ECO/Ex,  IECEx SEV 10.0003 certification for mining Gas Group 1,  temperature ranges of up to 150 deg C.

ATM/Ex

With compact housings in stainless steel or titanium, measuring ranges of up to 1000 bar and reverse polarity and short-circuit protection included, the ATM/Ex  pressure sensor is a suitable solution for industries where reliable and accurate pressure sensing is required within hazardous areas.

ATM/GR

The ATM/GR series 27 is a precision pressure transmitter based on the STS well proven ATM 23 series but incorporating two independent switch outputs adjustable over the full range of the transmitter. This transmitter with its excellent long term stability is capable of providing safety features in a wide range of industrial or process applications where pressure or level limits are critical.

ATM/T

A precision transmitter based on the well proven ATM 23 series but incorporating a PT100 measuring element to provide a dual output of either 4-20 mA or 0-5/10 VDC. Modular construction and the 20 year proven history of STS piezoresistive sensor technology provide manufacturing flexibility and fast delivery for all pressure ranges. Wide range of pressure and electrical connections available.

ATM

DTM

Compact and robust stainless steel piezoresistive assembly 1.4435 (316L)
Piezoresistive measuring element
Gauge, absolute or sealed gauge
All pressure ranges between 0…50 mbar and -1…1000 bar available
Calibration available for all common pressure units
High reliability
Customized versions due to modular assembly
Reverse polarity and short circuit protected
Media temperature up to 150°C (option)
Interface RS232C or RS485

PTM/Ex

Piezoresistive measuring element.  Pressure range from -5% till +105% FS until 1:4 adjustable measuring range 0 … 50 mbar and 0 … 1000 bar.  Output signal 4 ... 20 mA.  Calibration available for all common pressure units mH20, mWs, mWC etc.  Adjustable delay.  Reverse polarity and short circuit protected.  Active temperature compensation (option).

PTM/RS485

A fully digital programmable pressure transmitter providing the option of a 4-20mA analog output in addition to the standard RS485 MODBUS protocol. The transmitter offers the total accuracy of ≤± 0.15% FS including linearity, hysteresis, repeatability and thermal effects. The PTM also provides a precision temperature output thus offering a very high performance pressure/temperature sensor at a very affordable price.

PTM

The PTM series 40 is a high precision pressure transmitter, fully programmable over a dynamic range of 4:1 based on the full scale selected. The digital compensation provides high accuracy and general performance including linearity, hysteresis, repeatability and thermal effects while still providing a conventional 4-20mA 2-wire output for industrial and process applications

TM/Ex

Pressure ranges from 50 mbar to 1000 bar available. Intrinsic safety approval to II 1G EEx ia IIC T3…T6 and II 1D T90°C IP 6X. Ratiometric output signal in addition to input terminal voltage.

TM

The TM series 21 is a precision passive pressure transducer offering high performance and rugged flexible design for a wide range of industrial and OEM applications.  The transducer is based on STS piezoresistive sensor technology with 20 years proven history.  Low current consumption and pulsed operation make this an ideal pressure transducer for remote applications for long term operation and where limited power is available

TS100

Compact and robust stainless steel assembly 1.4435 (316L). Pt 100 measuring element according to DIN IEC 751 class A. Max. pressure up to 850 bar. Customized temperature ranges. Complies with the EMC directive 89/336/EEC. High reliability. Short delivery time. Customized versions due to modular assembly. Reverse polarity and short circuit protected.

EB100

The new EB100 series of pressure transducers is the smallest design proposed by MEAS from the UltraStable™ line. The EB100 sets a new price / performance standard for demanding commercial and heavy industrial applications where high accuracy, small size and low weight are desirable. This series is suitable for measurement of liquid or gas pressure, including difficult media such as contaminated water, steam, and mildly corrosive fluids.

4000

The 4000 series provides exceptional levels of stability and other performance specifications in a wide variety of enclosures from submersible to differential styles. By using a sputtered sensing element, which achieves a molecular fusion of a strain gauge material, an insulating material, and the 17-4 PH ss sensing element, the 4000 series transmitter provides the most stable sensor construction possible. These sputtered sensors are packaged for harsh applications requiring long term submersible service where precise laboratory type measurements are required.

2400

3300

For OEMs who need consistent high levels of performance, reliability and stability the 3300 Series pressure transmitter offers a small package size with all stainless wetted parts at an unbeatable price/performance ratio. A wide choice of electrical outputs as well as both electrical and pressure connections means the unit is suitable for most applications without modification. The compact construction of the 3300 series makes it ideal for installation where space is at a premium.
 

3100/3200

For OEMs who need consistent high levels of performance, reliability and stability the 3300 Series pressure transmitter offers a small package size with all stainless wetted parts at an unbeatable price/performance ratio. A wide choice of electrical outputs as well as both electrical and pressure connections means the unit is suitable for most applications without modification. The compact construction of the 3300 series makes it ideal for installation where space is at a premium.
 

Precise DPX3000

The PRECISE Digital Pressure Transmitter is an ultra high accuracy digital pressure and temperature sensor designed for high pressure measurement in critical applications in harsh environments where accuracy and stability of data are key to system performance.

EPXN

The EPXN is a high performance small pressure sensor using a silicon chip for clean media (non corrosive). With it's recessed port, it is best recommended for static applications or low frequency. Available with 10-32UNF or M5 thread, EPXN is available with a cable or integral connector.

EPXO

The EPXO is a high performance, stainless steel flush diaphragm. It is designed for high temperature, high stability, and high sensitivity applications. 

EPRB 3

Ultra miniature pressure transducer with platinum RTD to sense media temperature, 100% stainless steel welded construction with amplified output, designed for severe environment where minimum size and weight are required.

EPRB 2

Miniature pressure transducer, 100% stainless steel welded construction with amplified output, designed for severe environment where minimum size and weight are required.

EPX

The EPX is a miniature threaded pressure sensor with stainless steel flush diaphragm compatible with general media. Threads M5x0.8 or 10-32 UNF are available with built-in 0-ring seal for an easy installation. The EPX is offered in many pressure ranges from 0.35 to 350 bar (5 to 5000 psi) with gage, sealed gage, or absolute pressure reference. Non standard excitation, compensated temperatures, cable and thread lengths are available as options.

EPB

EPB is a small pressure probe sensor, small profile, stainless steel, flush mount transducer designed for general media. Resonant frequency 55 through 400 kHz makes it suitable for both static and dynamic measurements.

EPRB 1

Ultra miniature pressure transducer, 100% Stainless Steel welded construction with amplified output, designed for severe environment where minimum size and weight are required.

EPIH

The EPIH is a subminiature pressure sensor, specifically designed for Dynamic and High Frequency measurements with resonant frequency up to 1.7 MHz. Available with many various housings, EPIH is one of the smallest pressure sensors in the world.

EPL

The EPL is a surface mount pressure sensor with a stainless steel diaphragm. Available in ranges from 5 to
5000 psi (0.35 to 350 bar), EPL is easy to install on flat surfaces using elastomer or epoxy. Various compensated
temperature ranges are available from -40°C up to 90°C.