PML 1000

The PML1000 is an AC line powered LVDT/RVDT panel meter that is ideal for industrial and test applications. It features a 5 digit variable brightness LED display. For control applications, it has a fast (125 Hz) unscaled analog output, an isolated 0-10 VDC/4-20 mA scaleable output and optional serial 2 or 4 wire RS 422/485 communications.

ESAM Traveller Static

ESAM TRAVELLER Static is a high-performance signal conditioner/amplifier system mainly for static and quasi-static measurements in experimental stress analysis when medium or high numbers of input channels are required. The system accepts inputs from strain gauges in all common bridge configurations, from strain gauge based transducers, from potentiometers, and from general voltage sources.  It also accepts inputs from 4-bits digital signal sources

ESAM Traveller 1

ESAM TRAVELLER 1 is a high-performance digital data acquisition system for amplifying and conditioning of analogue sensor signals. The Master Unit represents the heart of the system. In a very small cabinet it contains: The power supply, the USB-Interface with a  RAM-data buffer, the A/D-Converter as well as 8 modules of Model SGA3 strain gauge bridge amplifiers. The system can easily be extended up to a 32 channels capacity by simply adding  max. 3 Extension Units with 8 channels each of Model SGA3 strain gauge bridge amplifiers.
 

DL/N/Ex

Feature: Battery operation, Measurement interval 2s…24h, 130'000 Measurement values

DL/N 70

Stainless steel

Feature: Battery operation, Measurement interval 0.5s…24h, 500'000 Measurement values

GSM

101

The Model 101 is a new, 3-Channel DC Signal Conditioner Amplifier designed to be used with bridge type or differential output accelerometers and pressure transducers. The Model 101 incorporates variable gain adjustment, shunt calibration capability, and multiple excitation level settings.

161

The Model 161 series is a 4-channel signal conditioning amplifier designed to be used with piezoelectric accelerometers (IEPE or Charge) and most other piezoelectric based transducers. The Model 161 series incorporates front-panel controlled gain adjustments, multiple high-pass and low-pass filter settings, and it is capable of displaying IEEE 1451.4 TEDS information.

PSD 704

Universal Analog Measurement Module (e.bloxx)

Sample rates up to 1000 Hz andresolutions up to 19 bit are possible depending on the module and signaltype used. Standardized communication protocols (Profibus-DP andModbus-RTU) allow the e.bloxx family to work with a wide variety ofapplication hardware and software.

With the addition of an e.gate the data throughput and connectivity options increase dramatically. The e.gate is a data concentrator and communication gateway, with 100 Mbps Ethernet and 12 Mbps Profibus-DP ports standard.

 

e.rack A6-16 Slimline

The e.rack slimline is a low profile rack mount design, and easily connects to the wide variety of field devices used in today's test beds.  Sample rates up to 1000Hz and resolutions up to 19bit are possible depending on the unit and signal type used.

Standardized communication protocols (Profibus-DP and Modbus-RTU) allow the e.rack slimline family to work with a wide variety of application hardware and software (including e.bloxx)

Load Cell Amplifier 121/122

Miniature Load Cell Amplifier 2818

PAK-II

PAK Mobil MK II is our compact mobile multi-channel measuring system for vibration-technological and acoustic analysis - a measuring front end for the most exacting user. It can be universally configured for any common measurement pickups and is easy to adapt to the task at hand. This reduces the effort required, speeds up your project, and minimizes your cost.

A laptop communicates with the measuring front end via a standard ethernet (10 or 100 Mbit/s and even 1 GBit/s) - wireless LAN is also an option. The computer is used to clearly display measured data online in real time, set channels and visualize recording level, synchronize measurements with rpm, and to analyze and interpret measured data.

Rebel XT

The Rebel XT can acquire vehicle data remotely and without user interaction, from serveral data sources reliably for long periods of time. Excellent data logger for collecting data from vehicles remotely. CAN Logging System

DiaLog

• Construct complex data logging configurations using an intuitive graphical interface. 
• Collect data using ISO 14229 and 15765 Diagnostic Protocols, CCP/xCP and directly from a CAN bus.
• Efficient database system allows simple administration of configurations and data.
• USB, GPRS and Bluetooth connectivity to Rebel data logger.
• Reconfigure and retrieve data by direct and remote connections.
• Live connection allows real time review of data while recording.

H box

The H Box is an extension to the Rebel TX data logger (CAN Logging System) allowing a variety of sensor inputs to be converted into the CAN format.  

SureFleet

The SureFleet gives access to data collected from vehicles by an onboard Rebel xt logger (CAN Logging System) from anywhere in the world in real time.  The data is streamed via GPRS to a dedicated server from where the data can be processed.

DL/Ex

Battery operation, Measurement interval 2s…24h, 130'000 Measurement values. ATEX approved for use in hazardous areas, eg landfill, fuel tanks.

4318 Amplifier

The 4318 amplifier is a straightforward digital set-up analogue amplifier that offer high performance and great versatility.  The amplifier is addressable and can be ganged together in up to 16 units.

LC 11 - Calog

It can test a loadcells' zero balance, input resistance, output resistance, bridge balance, 50V DC insulation test from bridge to shield, bridge to housing and shield to housing.

The Calog- Loadcell Calibrator is a hand-held precision calibrator specifically designed for load cell testing, including insulation breakdown and weighing system calibration or simulation. Simply connect a strain-gauge load cell to the spring terminals and press "TEST LOADCELL". The backlit graphics will display four or six wire, zero balance, input or output resistance and bridge balance. It can then carry out a 50 VDC insulation test form bridge to shield, bridge to housing and shield to housing.

For system testing and calibration the Calog- Loadcell Calibrator can simultaneously measure mV (with mass display), excitation voltage and mA. In source mode, used for load cell amplifier pre-calibration testing, it can source mV (with mass display), measure excitation and measure mA. In simulate mode it sources a mA signal to the control room or SCADA. The display can be in mA, mA and mass or mass and mA.

T211 Digital panel meter

The Tracker 211 can be directly connected to most popular process sensors including Thermocouple, RTD, 20mA loop Transmitters, DC signals up to 100mV and 10V. Temperature can be displayed in °C or °F to 0.1 degree resolution. Millivolt, 10 Volt and 20mA DC signals can be scaled to engineering units using any portion of the -1999 to 9999 display range.

T220

The Tracker 220 series indicators have a number of features which make them particularly suitable for the measurement of process signals. Maths functions allow calculations for orifice plate, “V” notch weir flow and rectangular (Cippaletti) weir flow. A filter is available for noisy or fast- moving signals. A 24 point user linearisation facility is provided for applications such as tank contents measurements.

T240

The Tracker 240 series of digital panel indicators are designed specifically for use with load cell transducers and for weighing applications. All the Tracker 240 series models have a 5 digit display and transducer supply plus many software features including tare, offset zeroing, ‘in-flight’ compensation, ‘peak picking’ and extensive alarm functions.  As standard the Tracker 240 series are fitted with an analogue output and an RS 422 /485 communications interface to allow connection to data loggers, chart recorders, PLCs and computers.

T300

The Tracker 300 series is a low cost Signal Conditioner, Trip Amplifier and PID Controller, for use in a variety of process applications. Its small size enables high packing density on standard TS35 DIN rail. A built in power supply, transmitter excitation and serial RS485 interface provides genuine single loop integrity with distributed data acquisition and control.

28000

The Precision 28000 makes it easy to manage a test with hundreds of channels and a mix of programmable transducers.  Choose bridge, charge, IEPE w/TEDS, voltage (filter amplifier), strain, thermocouple, RTD/potentiometer, frequency, or other transducers. Customize the 28000 for high-speed transient applications, static applications, or a combination of both.

4164

The Precision 4164 Switch Matrix System is a reliable solid-state switch matrix system in a compact rack mountable or bench top package providing computercontrolled connections between any input and any output. Connect between 64 input and 64 output channels with 4,096 cross points. Save time and reduce errors on your switch system setups. Program your switch configurations on a host computer, download them to your switch system over the network and your tests are ready to go. With system health monitoring, fault diagnostics and exhaustive self-tests, you can be confident of the integrity of your switch system

464kB

The 464kB is a 3-stage non-blocking solid state switching system which can provide the equivalent of a 256 x 256 rectangular coordinate switch with 65,536 cross points while using only 24,064 cross points. It uses 63% less cross points than a 256 x 256 rectangular coordinate switch, providing significant economy for large switching systems. This economy, as well as one-third the capacitive loading, is the main advantage of 3-stage switching systems.

The 464kB uses its test subsystem to verify the system integrity. A Go/No-Go test checks the integrity of the current setup. Running the FAT (Factory Acceptance Test) exhaustively tests all possible switch settings and reports which plug-in modules are defective.

PF-1U-FA

The PF-1U-FA series is a multi-channel programmable filter/amplifier system in a compact rack mountable or bench top package. Fully programmable 8-channel and 16-channel configurations are available in high performance or standard configurations.  The standard PF-1U-FA configuration offers 4-pole low-pass filters with five programmable cutoffs and gain programmable to x 1,024.

The high performance PF-1U-FA offers a choice of 4 or 8-pole low-pass and band-pass filters with cutoffs programmable from 1 Hz to 204.6 kHz. The high performance PF-1U-FA has an upgraded wideband (500 kHz) low-noise amplifier with transducer DC
suppress capability. Gain is programmable to x 8,192.

ESAM Traveller CF

Traveller CF is a Signal Conditioner Amplifier System with CF-Card data Storage. Flexible channel numbers and simple, straight forward operation procedures make the system meet the latest requirements of digital measurement technology and data processing. A built-in PCM-encoder enables telemetric operation with fast data transfer rates and high data security. System Traveller CF excellently satisfies all the sophisticated demands of stationary and mobile measurements of mechanical and electrical quantities.
 

Model SGA-0B Signal conditioner/Amplifer

• Analog signal conditioner/amplifier system with very high signal bandwidth and gain
• Analog signal bandwidth up to 120 kHz
• Gain up to 10 000 X
• Excitation voltage for all sensors up to 10 V
• Constant current excitation optional
• Operation via Software and USB-Interface
• Analog output ±10 V
• Inputs for strain gauges, strain gauge based transducers, and piezo-resistive sensors
• Stand-alone 1 channel, or multi-channel configuration

DL

Feature: Battery operation, Measurement interval 2s…24h, 130'000 Measurement values

DL/N

Feature: Battery operation, Measurement interval 2s…24h, 130'000 Measurement values